Supermicro 1026GT-TF Manuale Utente Pagina 15
- Pagina / 104
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your system up and running.
Following these steps in the order given should enable you to have the system
operational within a minimum amount of time. This quick setup assumes that your
system has come to you with the processors and memory preinstalled. If your sys-
tem is not already fully integrated with a serverboard, processors, system memory
etc., please turn to the chapter or section noted in each step for details on installing
specifi c components.
2-2 Unpacking the System
You should inspect the box the system was shipped in and note if it was damaged
in any way. If the server itself shows damage you should fi le a damage claim with
the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the server. It should
be situated in a clean, dust-free area that is well ventilated. Avoid areas where
heat, electrical noise and electromagnetic fi elds are generated. You will also need
it placed near a grounded power outlet. Read the Rack and Server Precautions in
the next section.
2-3 Preparing for Setup
The box the server was shipped in should include two sets of rail assemblies, two
rail mounting brackets and the mounting screws you will need to install the system
into the rack. Follow the steps in the order given to complete the installation process
in a minimum amount of time. Please read this section in its entirety before you
begin the installation procedure outlined in the sections that follow.
Choosing a Setup Location
Leave enough clearance in front of the rack to enable you to open the front door •
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for suffi cient airfl ow and ease in servicing.This product is for
installation only in a Restricted Access Location (dedicated equipment rooms,
service closets and the like).
- SUPER 1
- Manual Revision 1.0 2
- About This Manual 3
- Manual Organization 3
- Table of Contents 6
- Chapter 3 System Interface 7
- Chapter 4 System Safety 7
- Chapter 1 9
- Introduction 9
- 1-2 Serverboard Features 10
- 1-3 Server Chassis Features 11
- 1-4 GPU Subsystem 12
- Chapter 1: Introduction 13
- System Block Diagram 13
- 1-5 Contacting Supermicro 14
- Chapter 2 15
- Server Installation 15
- Warnings and Precautions! 16
- Rack Mounting Considerations 17
- Assembling the Outer Rails 20
- Chapter 3 27
- System Interface 27
- 3-3 Control Panel LEDs 28
- 3-4 SATA Drive Carrier LEDs 29
- Chapter 4 31
- System Safety 31
- 4-3 ESD Precautions 33
- LITHIUM BATTERY 34
- BATTERY HOLDER 34
- Chapter 5 35
- Advanced Serverboard Setup 35
- 5-2 Serverboard Installation 36
- 5-3 Connecting Cables 37
- 5-4 I/O Ports 38
- Socket Clip Load Plate 39
- Plastic Cap 39
- CPU Socket 40
- Load Plate 40
- Installing a CPU Heatsink 41
- 5-6 Installing Memory 42
- DIMM Population Table 43
- 5-6 Adding PCI Add-On Cards 44
- 5-7 Serverboard Details 45
- X8DTG-DF Quick Reference 46
- 5-8 Connector Defi nitions 47
- 5-9 Jumper Settings 53
- 5-10 Onboard Indicators 55
- 5-11 SATA Ports 56
- 5-12 Installing Software 57
- Supero Doctor III 58
- Chapter 6 61
- Advanced Chassis Setup 61
- 6-2 Control Panel 62
- 6-3 System Cooling 62
- System Fan Failure 63
- Figure 6-3: Fan Numbering 64
- Installing the Air Shroud 65
- Accessing the Drive Bays 65
- Hard Drive Installation 65
- 6-5 Power Supply 68
- Chapter 7 69
- 7-2 Main Setup 70
- XBoot Features 72
- Power Confi guration 73
- Processor and Clock Options 73
- XAdvanced Chipset Control 75
- XCPU Bridge Confi guration 75
- XNorth Bridge Confi guration 78
- XSouth Bridge Confi guration 78
- IDE/SATA/Floppy Confi guration 79
- XPCI/PnP Confi guration 82
- XRemote Access Confi guration 83
- Hardware Health Confi guration 84
- XACPI Confi guration 86
- XGeneral WHEA Confi guration 87
- XIPMI Confi guration 87
- View BMC System Event Log 87
- Set LAN Confi guration 88
- IP Address Confi guration 89
- MAC Address Confi guration 89
- Subnet Mask Confi guration 89
- 7-4 Security Settings 90
- 7-5 Boot Confi guration 92
- 7-6 Exit Options 93
- 7-7 BIOS Recovery 94
- Flash") 95
- Confirm update BIOS? (y/n) y 96
- Starting remote flash 96
- Appendix A 99
- BIOS Error Beep Codes 99
- Appendix B 101
- System Specifi cations 101
Prodotti e manuali riguardandi Server barebone Supermicro 1026GT-TF
(98 pagine)
(42 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.125 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale