Supermicro SuperServer 6015B-T+V, Silver Manuale Utente

®SUPERSERVER 6015B-T+SUPERSERVER 6015B-8+ USER’S MANUAL1.0a SUPER

SUPERSERVER 6015B-T+/6015B-8+ ManualxNotes

A-2SUPERSERVER 6015B-T+/6015B-8+ User’s ManualSystem CMOS checksum bad - Default confi guration usedSystem CMOS has been corrupted or modifi ed incorrec

A-3Appendix A: BIOS POST MessagesSystem cache error - Cache disabledRAM cache failed and BIOS disabled the cache. On older boards, check the cache jum

A-4SUPERSERVER 6015B-T+/6015B-8+ User’s ManualFixed Disk nFixed disk n (0-3) identifi ed.Invalid System Confi guration DataProblem with NVRAM (CMOS) dat

A-5Appendix A: BIOS POST MessagesParity Check 2 nnnnParity error found in the I/O bus. BIOS attempts to locate the address and display it on the scree

A-6SUPERSERVER 6015B-T+/6015B-8+ User’s ManualNotes

Appendix B: BIOS POST CodesB-1This section lists the POST (Power On Self Test) codes for the PhoenixBIOS. POST codes are divided into two categories:

B-2SUPERSERVER 6015B-T+/6015B-8+ User’s ManualPOST Code Description18h 8254 timer initialization1Ah 8237 DMA controller initialization1Ch R

Appendix B: BIOS POST CodesB-3POST Code Description5Ch Test RAM between 512 and 640 kB60h Test extended memory62h Test extended memory ad

B-4SUPERSERVER 6015B-T+/6015B-8+ User’s ManualPOST Code Description99h Check for SMART Drive (optional)9Ah Shadow option ROMs9Ch Set up Po

Appendix B: BIOS POST CodesB-5POST Code DescriptionCDh Re-map I/O and memory for PCMCIACEh Initialize digitizer and display messageD2h Unkn

Chapter 1: Introduction1-1Chapter 1 Introduction1-1 OverviewThe SuperServer 6015B-T+/6015B-8+ is a high-end dual processor, 1U rack-mount server

B-6SUPERSERVER 6015B-T+/6015B-8+ User’s ManualNotes

Appendix C: Software InstallationC-1 Appendix C Software InstallationAfter all the hardware has been installed, you must fi rst confi gure Intel&apos

C-2SUPERSERVER 6015B-T+/6015B-8+ ManualThe Intel HostRAID Confi gurationsThe following types of Intel's HostRAID confi gurations are supported:RAID

Appendix C: Software InstallationC-3Using the Intel ESB2 SATA RAID Utility Program1. Creating, Deleting and Resetting RAID Volumes: a. After the syste

C-4SUPERSERVER 6015B-T+/6015B-8+ Manualb. Specify a name for the RAID 0 set and press the <Tab> key or the <Enter> key to go to the next fi

Appendix C: Software InstallationC-5Creating a RAID 1 Volume:a. Select "Create RAID Volume" from the main menu and press the <Enter> k

C-6SUPERSERVER 6015B-T+/6015B-8+ ManualCreating a RAID 10 (RAID 1+ RAID 0):a. Select "Create RAID Volume" from the main menu and press the &

Appendix C: Software InstallationC-7Creating a RAID 5 Set (Parity):a. Select "Create RAID Volume" from the main menu and press the <Enter

C-8SUPERSERVER 6015B-T+/6015B-8+ ManualDeleting RAID Volume: (Warning: Be sure to back up your data before deleting a RAID set. You will lose

Appendix C: Software InstallationC-9Resetting to Non-RAID and Resetting a RAID HDD a. From the main menu, select item3-Reset Disks to Non- RAID, and

SUPERSERVER 6015B-T+/6015B-8+ Manual1-21-2 Serverboard FeaturesAt the heart of the SuperServer 6015B-T+/6015B-8+ lies the X7DBR-i+/X7DBR-8+ a dual Xeo

C-10SUPERSERVER 6015B-T+/6015B-8+ ManualC-2 Installing the Windows XP/2000/2003 for systems with RAID FunctionsNew Operating System-Windows XP/2000

D-1Appendix D: System Specifi cationsAppendix DSystem Specifi cationsProcessors Single or dual Intel® Xeon™ 5100/5000 Sequence processors at a fro

D-2SUPERSERVER 6015B-T+/6015B-8+ User's ManualExpansion Slots (provided with included riser cards) One (1) 64-bit, 133 MHz PCI-X slot for a st

D-3Appendix D: System Specifi cationsRegulatory Compliance Electromagnetic Emissions: FCC Class A, EN 55022 Class A, EN 61000-3-2/-3-3, CISPR

D-4SUPERSERVER 6015B-T+/6015B-8+ User's ManualNotes

Chapter 1: Introduction1-3Note: The operating system you use must have RAID support to enable the hot-swap capability and RAID function of the SCSI dr

SUPERSERVER 6015B-T+/6015B-8+ Manual1-41-3 Server Chassis FeaturesThe SC815TQ-700/SC815S-700 is one of Supermicro's third-generation 1U chas-sis

Chapter 1: Introduction1-5Figure 1-1. Intel 5000P/ESB2 Chipset: System Block Diagram Note: This is a general block diagram. Please see Chapter 5 for

SUPERSERVER 6015B-T+/6015B-8+ Manual1-61-4 Contacting Super MicroHeadquarters Address: Super Micro Computer, Inc. 980 Rock Av

Chapter 2: Server Installation2-1 Chapter 2 Server Installation 2-1 OverviewThis chapter provides a quick setup

2-2SUPERSERVER 6015B-T+/6015B-8+ ManualChoosing a Setup Location - Leave enough clearance in front of the rack to enable you to open the front do

Chapter 2: Server Installation2-3Rack Mounting ConsiderationsAmbient Operating TemperatureIf installed in a closed or multi-unit rack assembly, the am

Unless you request and receive written permission from SUPER MICRO COMPUTER, you may not copy any part of this document.Information in this document i

2-4SUPERSERVER 6015B-T+/6015B-8+ ManualInstalling the Rack RailsBegin by joining one set of rack rails corresponding to either the left or the right s

Chapter 2: Server Installation2-5Installing the Chassis RailsTwo of the chassis rails (Chassis Rail 1) should have already been preattached - one to e

2-6SUPERSERVER 6015B-T+/6015B-8+ ManualFigure 2-3. Installing the Server into a RackInstalling the Server into the RackYou should now have rails atta

Chapter 2: Server Installation2-7Figure 2-4. Installing the Server into a Telco RackInstalling the Server into a Telco RackTo install the 6015B-T+/6

2-8SUPERSERVER 6015B-T+/6015B-8+ Manual2-5 Checking the Serverboard SetupAfter you install the 6015B-T+/6015B-8+ in the rack, you will need to open

Chapter 2: Server Installation2-9Figure 2-5. Accessing the Inside of the Syatem (with optional front bezel shown)2-6 Checking the Drive Bay SetupNex

2-10SUPERSERVER 6015B-T+/6015B-8+ Manual4. Check the airfl ow Airfl ow is provided by four heavy duty 40-mm blower fans. The system compo-nent la

Chapter 3: System Interface3-1Chapter 3 System Interface3-1 OverviewThere are several LEDs on the control panel as well as others on the SATA/S

3-2SUPERSERVER 6015B-T+/6015B-8+ User's Manual3-3 Control Panel LEDsThe control panel located on the front of the SC815TQ-700/SC815S-700 chassis

Chapter 3: System Interface3-3 Power: Indicates power is being supplied to the system's power supply units. This LED should normally be illu

PrefaceAbout This ManualThis manual is written for professional system integrators and PC technicians. It provides information for the installation a

3-4SUPERSERVER 6015B-T+/6015B-8+ User's ManualNotes

Chapter 4: System Safety4-1 Chapter 4 System Safety!Basic electrical safety precautions should be followed to protect yourself from

SUPERSERVER 6015B-T+/6015B-8+ User's Manual4-24-2 General Safety PrecautionsFollow these rules to ensure general safety:  Keep the area around

Chapter 4: System Safety4-34-3 ESD Precautions Electrostatic discharge (ESD) is generated by two objects with different electrical charges co

SUPERSERVER 6015B-T+/6015B-8+ User's Manual4-44-4 Operating Precautions Care must be taken to assure that the chassis cover is in place

Chapter 5: Advanced Serverboard Setup5-1 Chapter 5 Advanced Serverboard SetupThis chapter covers the steps required to install pro

5-2SUPERSERVER 6015B-T+/6015B-8+ User’s ManualIMPORTANT: Always connect the power cord last and remove it fi rst before add-ing, removing or changing a

Chapter 5: Advanced Serverboard Setup5-3Socket keyCPU installed in socketPnP cap released from load plate3. Use your thumb and your index fi nger to ho

5-4SUPERSERVER 6015B-T+/6015B-8+ User’s ManualWarning! We do not recommend removal of the heatsink. However, if you do need to uninstall the heatsink

Chapter 5: Advanced Serverboard Setup5-55-3 Connecting CablesNow that the processors are installed, the next step is to connect the cables to the ser

SUPERSERVER 6015B-T+/6015B-8+ ManualivChapter 4: System SafetyYou should thoroughly familiarize yourself with this chapter for a general overview of

5-6SUPERSERVER 6015B-T+/6015B-8+ User’s ManualFigure 5-3. Front Control Panel Header Pins (JF1)Connecting the Control PanelJF1 contains header pins fo

Chapter 5: Advanced Serverboard Setup5-75-4 I/O PortsThe I/O ports are color coded in conformance with the PC 99 specifi cation. See Figure 5-4 below

5-8SUPERSERVER 6015B-T+/6015B-8+ User’s ManualFigure 5-5. Installing DIMM into SlotMemory SupportThe X7DBR-i+/X7DBR-8+ supports up to 64 GB of FBD (Fu

Chapter 5: Advanced Serverboard Setup5-95-6 Adding PCI Cards1. PCI slots The X7DBR-i+/X7DBR-8+ has two PCI expansion slots, which includes one

5-10SUPERSERVER 6015B-T+/6015B-8+ User’s Manual Figure 5-6. SUPER X7DBR-8+ Layout(not drawn to scale)5-7 Serverboard DetailsSUPER X7DBR-8+Not

Chapter 5: Advanced Serverboard Setup5-11X7DBR8+ Quick ReferenceJumper Description Default Setting J3P 3rd Power Fail Detect Open (Disable

5-12SUPERSERVER 6015B-T+/6015B-8+ User’s Manual5-8 Connector Defi nitions Power LED The Power LED connection is located on pins 15 and 16 of JF1. Refe

Chapter 5: Advanced Serverboard Setup5-13Overheat/Fan Fail LED (OH)Connect an LED to the OH connection on pins 7 and 8 of JF1 to provide ad-vanced war

5-14SUPERSERVER 6015B-T+/6015B-8+ User’s ManualReset Button The Reset Button connection is lo-cated on pins 3 and 4 of JF1. Attach it to the hardware

Chapter 5: Advanced Serverboard Setup5-15Fan HeadersThe X7DBR-i+/X7DBR-8+ has fi ve fan headers, designated Fan1 through Fan5. Fan speed is controlled

vPrefaceNotes

5-16SUPERSERVER 6015B-T+/6015B-8+ User’s ManualATX PS/2 Keyboard and PS/2 Mouse PortsThe ATX PS/2 keyboard and the PS/2 mouse ports are located on the

Chapter 5: Advanced Serverboard Setup5-17Wake-On-LANThe Wake-On-LAN header is desig-nated WOL. See the table on the right for pin defi nitions. You m

5-18SUPERSERVER 6015B-T+/6015B-8+ User’s ManualSGPIOThe two headers labeled SGPIO1 and SGPIO2 are for SGPIO (Serial General Purpose Input/Output). SG

Chapter 5: Advanced Serverboard Setup5-195-9 Jumper SettingsExplanation of JumpersTo modify the operation of the serverboard, jumpers can be used

5-20SUPERSERVER 6015B-T+/6015B-8+ User’s ManualJLAN Enable/Disable Change the setting of jumper JPL1 and JPL2 to enable or disable the on-board LAN po

Chapter 5: Advanced Serverboard Setup5-21SCSI Controller Enable/Disable (6015B-8+ only)Jumper JPA1 is used to enable or dis-able the onboard SCSI cont

5-22SUPERSERVER 6015B-T+/6015B-8+ User’s ManualCompact Flash Master/Slave SelectA Compact Flash Master (Primary)/Slave (Secondary) Select jumper is l

Chapter 5: Advanced Serverboard Setup5-235-10 Onboard IndicatorsJLAN1/JLAN2 LEDsThe Ethernet ports (located beside the VGA port) have two LEDs. On ea

5-24SUPERSERVER 6015B-T+/6015B-8+ User’s Manual5-11 Floppy, IDE, SATA and SCSI Drive ConnectionsNote the following when connecting the fl oppy and har

Chapter 5: Advanced Serverboard Setup5-25IDE Drive ConnectorsPin Defi nitions (IDE#1, IDE#2)Pin# Defi nition Pin # Defi nition1

SUPERSERVER 6015B-T+/6015B-8+ ManualviTable of ContentsPrefaceAbout This Manual ...

5-26SUPERSERVER 6015B-T+/6015B-8+ User’s ManualSATA PortsThere are no jumpers to confi gure the onboard SATA connectors. See the table on the right fo

Chapter 5: Advanced Serverboard Setup5-27Ultra320 SCSI Drive PortPin Defi nitions (JA1/JA2)Pin# Defi nition Pin # Defi nition1

5-28SUPERSERVER 6015B-T+/6015B-8+ User’s ManualNotes

Chapter 6: Advanced Chassis Setup6-1Chapter 6Advanced Chassis Setup This chapter covers the steps required to install components and perform m

6-2SUPERSERVER 6015B-T+/6015B-8+ ManualFigure 6-1. Chassis: Front and Rear ViewsSystem Reset6-2 Control PanelThe control panel (located on the front

Chapter 6: Advanced Chassis Setup6-36-3 System FansFour 40-mm heavy duty counter-rotating fans provide the cooling for the SuperServer 6015B-T+/6015B-

6-4SUPERSERVER 6015B-T+/6015B-8+ ManualFigure 6-2. System Cooling Fans6-4 Drive Bay Installation/RemovalRemoving the Front BezelIf your system has a

Chapter 6: Advanced Chassis Setup6-5Accessing the Drive BaysSATA/SCSI Drives: Because of their hotswap capability, you do not need to access the insid

6-6SUPERSERVER 6015B-T+/6015B-8+ ManualSATA/SCSI Drive Installation1. Mounting a SATA/SCSI drive in a drive carrier The SATA and SCSI drives are

Chapter 6: Advanced Chassis Setup6-72. Installing/removing hot-swap SATA/SCSI drives The SATA/SCSI drive carriers are all easily accessible at th

Power ... 3-33-4 Drive Carrier LEDs ...

6-8SUPERSERVER 6015B-T+/6015B-8+ ManualDVD-ROM and Floppy Drive InstallationThe top cover of the chassis must be opened to gain full access to the DVD

Chapter 6: Advanced Chassis Setup6-96-5 Power SupplyThe SuperServer 6015B-T+/6015B-8+ has a single 700 watt power supply, which is auto-switching capa

6-10SUPERSERVER 6015B-T+/6015B-8+ ManualFigure 6-6. Removing/Replacing the Power Supply

Chapter 7: BIOS7-1Chapter 7 BIOS 7-1 Introduction This chapter describes the Phoenix BIOS™ Setup utility for the X7DBR-8+/X7DBR-i+. The P

7-2SUPERSERVER 6015B-T+/6015B-8+ Manual7-2 Running Setup*Default settings are in bold text unless otherwise noted.The BIOS setup options described in

Chapter 7: BIOS7-3Main BIOS Setup MenuMain Setup FeaturesSystem TimeTo set the system date and time, key in the correct information in the appropriate

7-4SUPERSERVER 6015B-T+/6015B-8+ ManualIDE Channel 0 Master/Slave, IDE Channel 1 Master/Slave, SATA Port2 and SATA Port3These settings allow the user

Chapter 7: BIOS7-5CHS FormatThe following items will be displayed by the BIOS:TYPE: This item displays the type of IDE or SATA Device.Cylinders: This

7-6SUPERSERVER 6015B-T+/6015B-8+ ManualParallel ATAThis setting allows the user to enable or disable the function of Parallel ATA. The options are D

Chapter 7: BIOS7-7System MemoryThis display informs you how much system memory is recognized as being present in the system.Extended MemoryThis displa

SUPERSERVER 6015B-T+/6015B-8+ ManualviiiExtra USB Headers ... 5-16Power

7-8SUPERSERVER 6015B-T+/6015B-8+ ManualBoot FeaturesAccess the submenu to make changes to the following settings.QuickBoot ModeIf enabled, this featu

Chapter 7: BIOS7-9Memory CacheCache System BIOS AreaThis setting allows you to designate a reserve area in the system memory to be used as a System B

7-10SUPERSERVER 6015B-T+/6015B-8+ ManualSelect "Uncached" to disable this function. Select "Write Through" to allow data to be cac

Chapter 7: BIOS7-11Slot1 PCI-X 133MHz, Slot2 PCI-Exp x8/x4, Slot3 PCI-Exp x4, Slot4 PCI-Exp x8 and Slot5 PCI-Exp x8 Access the submenu for each of

7-12SUPERSERVER 6015B-T+/6015B-8+ ManualMemory Branch ModeThis option determines how the two memory branches operate. System address space can either

Chapter 7: BIOS7-13Advanced Processor OptionsAccess the submenu to make changes to the following settings. CPU SpeedThis is a display that indicates

7-14SUPERSERVER 6015B-T+/6015B-8+ ManualAdjacent Cache Line Prefetch (Available when supported by the CPU.)The CPU fetches the cache line for 64 bytes

Chapter 7: BIOS7-15InterruptThis setting allows you to select the IRQ (interrupt request) for serial port A. The options are IRQ3 and IRQ4. Serial Po

7-16SUPERSERVER 6015B-T+/6015B-8+ ManualDMI Event LoggingAccess the submenu to make changes to the following settings. Event Log ValidityThis is a di

Chapter 7: BIOS7-17Console Redirection Access the submenu to make changes to the following settings. COM Port AddressThis item allows you to specify

Table of ContentsixRemoving the Front Bezel ... 6-4Accessing the Drive Bays ...

7-18SUPERSERVER 6015B-T+/6015B-8+ ManualHardware Monitor LogicNote: The Phoenix BIOS will automatically detect the type of CPU(s) and hardware monito

Chapter 7: BIOS7-19Hardware Monitor LogicCPU Temperature Threshold (See note on page 7-18.)This option allows the user to set a CPU temperature thres

7-20SUPERSERVER 6015B-T+/6015B-8+ ManualHardware Monitor Logic (See note on page 7-18.)CPU Temperature ThresholdThis option allows the user to set a

Chapter 7: BIOS7-21IPMI (The option is available only when an IPMI card is installed in the system.)IPMI Specifi cation Version: This item displays th

7-22SUPERSERVER 6015B-T+/6015B-8+ ManualOS Boot Watch DogSet to Enabled to enable OS Boot Watch Dog. The options are Enabled and Disabled.Timer for Lo

Chapter 7: BIOS7-23Realtime Sensor DataThis feature display information from motherboard sensors, such as temperatures, fan speeds and voltages of va

7-24SUPERSERVER 6015B-T+/6015B-8+ Manual7-5 SecurityChoose Security from the Phoenix BIOS Setup Utility main menu with the arrow keys. You should see

Chapter 7: BIOS7-25Password on BootThis setting allows you to require a password to be entered when the system boots up. The options are Enabled (pas

7-26SUPERSERVER 6015B-T+/6015B-8+ Manual7-7 ExitChoose Exit from the Phoenix BIOS Setup Utility main menu with the arrow keys. You should see the fol

A-1Appendix A: BIOS POST Messages Appendix A BIOS POST MessagesDuring the Power-On Self-Test (POST), the BIOS will check for problems.