Supermicro SYS-7046A-6 Manuale Utente Pagina 66
- Pagina / 98
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
6-8
SuperWorkstation 7046A-6 User's Manual
Installing Components in the 5.25" Drive Bays
The 7046A-6 has three 5.25" drive bays. Components such as SATA hard drives or
DVD/CD-ROM drives can be installed into these 5.25" drive bays.
Removing the Empty Drive Bay
First power down the system.1.
Remove the top/left chassis cover to access the drive components.2.
With the cover off, remove the screws that secure the drive carrier to the 3.
chassis (one side only) then push the entire empty drive carrier out from the
back.
Adding a DVD/CD-ROM Drive
Remove the guide plates (one on each side) from the empty drive carrier 1.
and screw them into both sides of the DVD/CD-ROM drive using the holes
provided.
Slide the DVD/CD-ROM into the bay and secure it to the chassis with the 2.
drive carrier screws you fi rst removed.
Attach the power and data cables to the drive.3.
Replace the top/left chassis cover and restore power to the system.4.
Adding a SATA Drive
Install an SATA drive into one of the removed empty drive carriers.1.
Secure the drive to the carrier with screws then slide the assembly into 2.
the bay and secure it to the chassis with the drive carrier screws you fi rst
removed.
Attach the power and data cables to the drive.3.
Replace the top/left chassis cover and restore power to the system.4.
Note: Drive carriers should remain in any empty drive bays to maintain proper
airfl ow within the chassis.
- SUPER 1
- Manual Revision 1.0 2
- About This Manual 3
- Manual Organization 3
- Table of Contents 6
- Chapter 3 System Interface 7
- Chapter 4 System Safety 7
- Chapter 1 9
- Introduction 9
- 1-2 Serverboard Features 10
- 1-3 Chassis Features 11
- Cooling System 12
- Chapter 1: Introduction 13
- System Block Diagram 13
- 1-4 Contacting Supermicro 14
- Chapter 2 15
- Installation 15
- Warnings and Precautions! 16
- Rack Mounting Considerations 17
- Inner rail 18
- Outer rail 18
- Rail brackets 18
- Installing the Chassis Rails 19
- Installing the Rack Rails 20
- Chapter 3 25
- System Interface 25
- 3-3 Control Panel LEDs 26
- 3-4 Drive Carrier LEDs 27
- Chapter 4 29
- System Safety 29
- 4-3 ESD Precautions 31
- LITHIUM BATTERY 32
- BATTERY HOLDER 32
- Chapter 5 33
- Advanced Serverboard Setup 33
- 5-2 Serverboard Installation 34
- 5-3 Connecting Cables 35
- 5-4 I/O Ports 36
- Memory Support 41
- 5-7 Adding PCI Add-On Cards 42
- 5-8 Serverboard Details 43
- X8DA6 Quick Reference 44
- 5-9 Connector Defi nitions 45
- 5-10 Jumper Settings 51
- 5-11 Onboard Indicators 54
- 5-14 Supero Doctor III 57
- Chapter 6 59
- Advanced Chassis Setup 59
- 8 SAS Drive Bays 60
- (behind locking bezel) 60
- System ResetMain Power 60
- 5.25" Drive Bays (3) 60
- USB Ports 60
- 6-2 Front Control Panel 61
- 6-3 System Fans 62
- 6-4 Drive Bay Installation 64
- SAS/SATA Backplane 65
- 6-5 Power Supply 67
- Chapter 7 69
- 7-2 Main Setup 70
- XBoot Features 72
- Power Confi guration 73
- Processor and Clock Options 73
- XAdvanced Chipset Control 76
- XCPU Bridge Confi guration 76
- XNorth Bridge Confi guration 77
- XSouthBridge Confi guration 78
- IDE/SATA Confi guration 79
- XPCI/PnP Confi guration 82
- XRemote Access Confi guration 83
- System Health Monitor 84
- XACPI Confi guration 86
- 7-4 Security Settings 88
- 7-5 Boot Confi guration 90
- 7-6 Exit Options 91
- Appendix A 93
- BIOS Error Beep Codes 93
- Appendix B 95
- System Specifi cations 95
- Regulatory Compliance 97
Prodotti e manuali riguardandi Server barebone Supermicro SYS-7046A-6
Server barebone Supermicro 6016T-MTHF Manuale Utente
(100 pagine)
(100 pagine)
Gold's Gym Deportes y recreación manuales de usuario
Empezando en G
Commenti su questo manuale